ASTM D1816 PDF

ASTM D – Standard Test Method for Dielectric Breakdown Voltage of Insulating Oils of Petroleum Origin. Using VDE Electrodes. ▫ IEC Insulating. Page 1. Page 2. Page 3. Page 4. Find the most up-to-date version of ASTM D at Engineering

Author: Gardami Zulmaran
Country: Uzbekistan
Language: English (Spanish)
Genre: Politics
Published (Last): 8 December 2018
Pages: 88
PDF File Size: 7.68 Mb
ePub File Size: 2.24 Mb
ISBN: 701-7-37598-395-6
Downloads: 11968
Price: Free* [*Free Regsitration Required]
Uploader: Vikazahn

The sample shall be taken in a dry, clean, non-permeable bottle. After adjustment of the spacing, rinse the cell with a dry hydrocarbon solvent, such as kerosine or solvents of Specification D IEEE Standard 4 is required during the manufacturing of the test apparatus and utilized during calibration of the equipment. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

If it is necessary to readjust the electrodes, lock the electrodes and check the spacing. Measurement of oil temperature: Request a Free Quote Right Now.

Reinstall the electrodes in the test cup and adjust spacing and clean in accordance with 7. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The equipment should produce a straight-line voltage-time curve over the operating range of the equipment. Automatic equipment should be used to control the voltage rate of rise because of the difficulty of maintaining a uniform voltage rise manually.

Providing the finest test equipment solutions since 1992

Pharmaceutical laboratory apparatus stability chambers, tablet disintegration, tablet dissolution, tablet hardness, V-blenders, Determination of the dielectric breakdown voltage of insulating oils provides an early detection method for any reduction in the insulating properties. However, a high dielectric breakdown voltage does not necessarily indicate the absence of all contaminants; it may merely indicate that the concentrations of contaminants that are present in the liquid between the electrodes are not large enough to deleteriously affect the average breakdown voltage d816 the liquid when tested by this test method see Appendix X1.

  HOJA DATOS 1N4001 PDF

Contact with us now Your mail: Plastic bottles are permeable and moisture content of the sample may change resulting f1816 a ashm difference when compared to samples collected in non-permeable containers. Petroleum Products and Biofuel lab apparatus baths, e1816, color measurement, density meters, flash point, hydrogenators, oil testing, penetrometers, surface tension, vapor pressure, viscometers and rheometers, The most important requirement of an insulating oil is a high dielectric strength.

Non-disruptive discharges in the test circuit should not reduce the test voltage to such an extent, and for such a time, that the disruptive discharge breakdown voltage of the test specimen is significantly affected. This test method should be used as recommended by professional organization standards such as IEEE C Link to Active This link will always route to the current Active version of the standard.

The residue from the buffing should be removed by repeated wiping with lint-free tissue paper saturated with a suitable solvent, followed by solvent rinsing or ultrasonic cleaning.

Refer to Terminology D for definitions used in this test method. Flat “go” and “no-go” gages astj be substituted having thicknesses of the specified value more or less 0. Oil d181 procedures are detailed in Practice D Do not use a low boiling point solvent, as its rapid evaporation may cool the cell, causing moisture condensation.

So that the breakdown may be observed, transparent materials are desirable, but not essential. If a dielectric breakdown does not occur during any of the consecutive breakdown tests using the 2 mm spacing or the sample is not adequate for the 2 mm spacing test cell a 1 more or less 0.

The quality of the insulating oil must be checked at regular intervals to ensure a long equipment service life. Looking for a specific close-up? The voltage in the test circuit should be stable enough to be unaffected by varying current flowing in the capacitive and resistive paths of the test circuit. USB memory stick Operating Temperature: Alternatively, the cell may be stored empty in a dust-free cabinet. Type text as it appears:: A cell having a capacity of 0.

Baur GmbH: Report Manager

After careful inspection, any electrodes from which pitting cannot be removed by light buffing should be discarded, as more refinishing would d1861 the electrode contour and dimensions shown in Fig. A lower than anticipated value is considered as evidence of cell contamination; then repeat the cleaning and the breakdown test with clean dry oil.

  ASTM D3034 PDF

Particular reference should be made to the general precaution statement of this test method. Email Us ast, call toll-free: This test method is applicable to insulating liquids commonly used in cables, transformers, oil circuit breakers, and similar apparatus as an insulating and cooling medium. It is recommended that the circuit design limit the disruptive current duration and magnitude to low values that will minimize damage to the electrodes and limit formation of non-soluble materials resulting from the breakdown, but consistent with the requirements of 4.

A test cell having a capacity of 0.

Clearance from the electrodes to all sides, bottom, cover or baffle, and any part of the stirring device is at least Construct the test cell of a material of high dielectric strength, that is not soluble in or attacked by any of the cleaning or test liquids used, and is nonabsorbent to moisture and the cleaning and test liquids.

Product Description The majority of high-voltage transformers, cables, switchgears, transducers, capacitors, and rectifiers use insulating oils for insulating electrically live parts and to carry off thermal energy. Tightly seal and shield from light until ready to be tested.

It is important to avoid touching the electrodes or the cleaned gage with the fingers or with portions of the tissue paper or chamois that have been in contact with the hands. General Use laboratory apparatus balances, baths, blenders, centrifuges, chart recorders, freezers, fume hoods, furnaces, glassware washers, glove boxes, mixers, moisture testing, ovens, pumps, shakers, vacuum equipment, water purification ASTM Method being used?

Adjustment and Asrm of Electrodes and Test Cell 7. Lab Equipment for D816

Posted in <a href="http://santovec.us/category/life/" rel="category tag">Life</a>