ASTM D5961 PDF

Procedure A in ASTM D , has the objective to test composite laminates double-edged. The pin in the device, creating two cutting plans, extracts a segment. ASTM D TESTING FIXTURE – PROCEDURE B. FASTENER BEARING SPECIMEN SUPPORT. Pdf icon button Download PDF. The bearing strength of a . Model No. ASTM.D – Double Shear Fastener Test Fixture. The Double Shear Fixture applies a double shear load via two loading plates secured to the.

Author: Kigazil Kidal
Country: Jordan
Language: English (Spanish)
Genre: Spiritual
Published (Last): 18 March 2016
Pages: 257
PDF File Size: 14.61 Mb
ePub File Size: 18.5 Mb
ISBN: 784-2-24085-759-9
Downloads: 18837
Price: Free* [*Free Regsitration Required]
Uploader: Motilar

ASTM D5961 Double Shear Fixture for Bearing Composite Laminate | GD5961-A

Procedure B is actually a specimen support fixture and is described in Section H-1 of this product catalog. The other three procedures are pin bearing fixtures, as will be described here.

That is, the pin in the fixture attempts to shear out a segment of the composite laminate test specimen by creating two shear planes in the pin. The standard test specimen is 5. The end of the fixture with the spacer in place is gripped in a standard tensile wedge grip. Each half of the fixture is 0.

The free end of the specimen is held in a second tensile wedge grip.

A tensile load is applied until a maximum loading has been reached, monitoring both applied force and hole deformation, as described in the ASTM standard. Asm the customer has a requirement to test non-standard specimen sizes, requiring Wyoming Test Fixtures, Inc.

  LINGUISTIK HISTORIS KOMPARATIF PDF

An alternate version of the test fixture shown in Figs.

As described in Section H-2, the SACMA fixture is much easier to use since the specimen holder is one piece, with adjustable bushings to accommodate asym in specimen thickness.

That is, a single shear plane is developed in the loading pin as the tensile load is applied.

ASTM D TESTING FIXTURE – PROCEDURE B

The test fixture is shown in Fig. The specimen is placed on the right surface of the test fixture, aligning the hole in the asrm of the specimen with the hole shown in the fixture and a fastener inserted and lightly torqued. Or a pin can be used. The flat tang at the top of the test fixture is gripped in a wedge grip and a tensile force is applied to the lower end of the specimen.

The maximum force attained and the deformation of the hole in the specimen are recorded. Procedure Ast, of ASTM D loads the laminate bearing specimen in double shear through a close-tolerance, lightly torqued fastener or pin. The fixture is shown in Fig.

ASTM D Polymer Matrix Composite Laminate Bearing Strength Test Equipment

The two lower components of the fixture are spread apart to permit inserting the 1. A pin or fastener is inserted in the hole, the fastener being torqued as desired.

  BAKTERI PSEUDOMONAS FLUORESCENS PDF

The upper end of the fixture is held in a grip, as is the lower end of the test specimen. The specimen is kept short enough to avoid buckling. The applied compressive loading induces a double shear in both the specimen asttm the loading fastener or pin. Load at failure and hole deformation are measured.

Sources of Additional Information:. This simple test fixture is shown in Fig. The two halves of the fixture are separated by a spacer not provided of the same thickness as the specimen being tested.

ASTM D 5961 TESTING FIXTURE – PROCEDURE B

Obviously, a piece of the same test material can be used as a spacer, if desired. Since a raised boss is present at the pin hole, the opposite end of the fixture is thicker by an equal amount so that the specimen is uniformly supported when gripped.

Sources of Additional Information: Wyoming Test Fixtures Inc.

Posted in <a href="http://santovec.us/category/life/" rel="category tag">Life</a>