ISO Plastics — Polyethylene (PE) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties. INTERNATIONAL. STANDARD. ISO. Third edition. Plastics — Polyethylene (PE) moulding and extrusion materials —. Part 2: Preparation of . This British Standard was published by BSI. It is the UK implementation of. EN ISO It supersedes BS EN ISO which.
|Country:||Turks & Caicos Islands|
|Published (Last):||17 June 2006|
|PDF File Size:||13.78 Mb|
|ePub File Size:||2.97 Mb|
|Price:||Free* [*Free Regsitration Required]|
Designation system and basis for specifications. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary isl pages This document comprises a front cover, an inside front cover, pages i and ii, the EN ISO title page, page 2, the ISO title page, pages ii to iv, pages 1 to 6 and a back 8172-2.
This standard has been updated see copyright 1827-2 and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Designation system and basis for specifications ISO Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Novemberand conflicting national standards shall be withdrawn at the latest by November The work 18722 preparing International Standards is normally carried out through ISO ieo committees.
Each isi body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part 11872-2 the work. Draft International Standards adopted by the iwo committees are circulated to the member bodies for voting. This second edition cancels and replaces the first edition ISO ISO consists of the following parts, under the general title Plastics — Polyethylene PE moulding and extrusion materials: Designation system and basis for specifications; — Part 2: Preparation of test specimens and determination of properties.
It applies to materials ready for normal use in the form of powder, granules 18722-2 pellets, unmodified or modified by colorants, additives, fillers, etc.
If such additional properties are required, they shall be determined in 18772-2 with the test methods specified in part 2 of this International Standard, if suitable. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO are encouraged to investigate the possibility of applying iiso most recent editions of the standards indicated below.
Basic polymers and their special characteristics. For unambiguous designation, the individual-item block is subdivided into five data blocks comprising the following information: The data blocks shall be separated from each other by commas. If a data block is not used, this shall be indicated by doubling the separation sign, i. The code-letters used are specified in Table 1.
If information is presented in positions 2 to 8 and no specific information is given in position 1, the letter X shall be inserted in position izo. Table 1 — Code-letters used in data block 2 3. The two code-numbers are separated from each other by hyphens. If a property value falls on or near a range limit, the manufacturer shall state which range will designate the material.
If subsequent individual test values lie on, or on either side of, the range limit because of manufacturing tolerances, the designation is not affected. NOTE 1 Not all the combinations of the values of the designatory properties are provided by currently available polymers.
Intended application or method of processing see 3. Positions 2 to 8: Important properties, additives and supplementary information see 3.
Designatory properties see 3. Fillers or reinforcing materials and their nominal content see 3. For the purpose of specifications, a fifth data block may be added containing additional information.
After being cut off, kso strand is allowed to fall on a cool metal plate. It is subsequently annealed by immersing it in ml of boiling water in a beaker, boiled for 30 min, and allowed to cool for 1 h by keeping the beaker and contents in the laboratory atmosphere.
BS EN ISO 1872-2:2007
The density of the specimen is then determined within iiso h in accordance with ISO The possible values of density are divided into 10 ranges, each represented by a 2-figure code-number as specified in Table 2. Table 2 — Code-numbers used for density in data block 3 3. The possible values of melt mass-flow rate are divided into 11 ranges, each represented by a 3-figure code-number as specified in Table 4.
The test conditions used shall be indicated by a single code-letter, as specified in Table 3, immediately preceding the code-number indicating the range. Subsequently without a spacethe mass content may 172-2 given by a 2-figure number in positions 3 and 4.
Table 5 — Code-letters for fillers and reinforcing materials in data block 4 3. This shall be done for example by reference to a suitable national standard or to a standard-like, generally established specification.
In the case of metals Mit is essential to indicate the type of metal by means of its chemical symbol. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.
It presents the UK view on standards in Europe and at the international level.
Plastic Testing Leader-Elastomers-Composites-Polymer testing PTLI
It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.
It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.
BSI offers members an individual ieo service called PLUS which ensures that subscribers automatically receive the latest editions 18722 standards.
ÖNORM EN ISO 06 01 – Webshop – Austrian Standards
Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through ieo Library and its Technical Help to Exporters Service.
Various BSI electronic information services are lso available which give details on all its products and services. Contact the Information Centre. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For 18722- of these and other benefits contact Membership Administration.
Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the ixo standardization bodies. Except 187-22 permitted under the Copyright, Designs and Patents Act no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means — electronic, photocopying, recording or otherwise — without prior written permission from BSI.
This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager.
ISO Material specifications and 1872–2 criteria for pipes, fittings and system.